FORGET THE REST CHOOSE THE BEST

VA5PRO

 

VIBRATION ANALYSIS
THERMAL IMAGING
ULTRASOUND MEASUREMENT

 

I’M FUNCTION LOADED.

Explore the most powerful Vibration Analyzer on the market.
Use multitasking tool in order to analyze your machinery.
Balancer, thermal imaging camera, ultrasound, bump test, ODS, MCSA – you name it…

I CAN FEEL IT…

FFT WITH UP TO 3 276 800 LINES

90 KHZ FREQUENCY RANGE

RAW SIGNAL RECORDING

OVERALLS, FRF, SMAX, ORBITS, CENTERLINE, CEPSTRUM ETC.

…you can analyze it.

I CAN SEE IT…

…so you can see it.

I CAN HEAR IT…

 

…then you can hear it too.

I CAN AMPLIFY THE MOVEMENT…

…and I can do much more.

VA5 MODULES

MAIN MENU

Analyzer, Route, Run Up, Recorder, Balancer, FASIT (Expert System), Stethoscope,
Lubri,
MCSA,
Octave Analysis,
Bump Test,
ADS (Operating Deflection Shapes),
Ultrasound,
Camera,
Thermal Imaging Camera,
Picture Gallery

ANALYZER

 Select the type of the measurement (from simple overall values through FFTs and time signals to more advanced measurements with Proximity probes such as Orbits), set up the measurement settings according to your requirements (frequency range, sampling, units etc.) and take all the predefined measurements simultaneo

BALANCER

The balancer allows you to perform one or two plane balancing job of rotating parts such as industrial fans, blowers, spindles etc.

RECORDER

A unique measurement mode with unappreciated value. Recorder “records” the raw signal from the sensor, means raw signal from the machine. This allows to make a post processing of the signal later on your PC. You can play this record again and again and apply any measurement setting to it.

IR CAMERA

 The thermal imaging camera gives you another sense. Find overheated bearings, loose electrical connections, blocked pipes on heat exchangers and other industrial problems.

FASIT

  • FASIT ( Fault Source Identification Tool) is an expert system for automatic detection of possible machine faults
  • Unbalance
  • Misalignment
  • Looseness
  • Bearing Faults

ROUTE

The route module is used for day to day data collection of your factory machinery. Simply create your route tree with measurement points location in DDS software and take the measurements regularly. Transfer collected data to DDS software to watch the trends and analyze the data.
</p>

MCSA

Motor current signature analysis is a useful tool
for electric motors inspection. Especially for detection of broken rotor bars, air gap eccentricity, shorted turns in stator windings and power quality.

OCTAVE ANALYSIS

Octave analysis allows you to measure audible sound. Connect your ICP microphone and measure sound level and Octave spectrum with selectable 1/1, 1/3, 1/12, 1/24 resolution.

ADS

Animated Deflection Shapes software is based on the method of operating deflection shapes. This means we visualize the vibrations of certain machine by animation. During the animation the vibration movement is slowed down to very low frequency and the amplitude of the motion isincreased so we can see the vibration. You can animate the machine motion directly on the VA5 Pro device!

ULTRASOUND

 Measurement of sound inaudiable to the human ear – ultrasound. Typical application are air leak detection, electrical arcing or early bearing fault detection.

RUNUP

Similar to Analyzer mode where you can setup any measurement which you like. RunUp allows you to control the saving of data for example as soon as possible, or by speed change, time change etc.

LUBRI

Lubri is a maintenance tool used for monitoring and control of the lubrication process. Lubri measures the actual bearing lubrication status and informs the operator when the lubrication state is optimal.

STETHOSCOPE

Do not use a screw driver to listen your bearing noise anymore. Place the sensor on the bearing house and listen the machine / bearing noise with headphones. VA5 Pro enables to listen signals from 4 channels. Just switch between individual channels. Adjust the volume according to your needs.

BUMP TEST

 An easy way how of measuring structure resonance frequencies. No need for any settings, just place the sensor on the structure and hit it with the appropriate hammer.

CAMERA

The built-in camera helps you to organize maintenance jobs. Is there any visible oil leak, loose part or other issue? Capture it on camera and send it to responsible person for further action.

GALLERY

All your pictures from camera, IR camera and measurement screenshots are stored in one place. The gallery is a useful management tool for all your captures.

VIBRATION ANALYST DREAM

Measure 4 vibration signals and 4 process values (temperature, pressure etc.) along with speed synchronously. Triaxial sensor friendly, proximity probes for displacement measurement, ultrasound microphone, acoustic microphone, thermal imaging camera, current clamp meter, stethoscope and more.

VA5 TECHNICAL SPECIFICATIONS

INPUT CHANNELS : 

4 x AC, ICP® power supply on/off
4 x DC for process values
1 x TACHO for speed probe/external trigger

INPUT RANGE:

AC +/- 12 V peak-peak
DC +/- 24V

AD CONVERSION

24 bit, 64 bit internal signal processing
No AutoGain function!

DYNAMIC RANGE S/N: 

120 dB

FREQUENCY RANGES  (-3 dB):

Maximum range: 0.35 Hz – 90 kHz (1 Ch, 194 kHz sampling)
Maximum range: 0.35 Hz – 25 kHz (4 Ch, 64 kHz sampling)
Minimum range: 0.35 Hz – 25 Hz (4 Ch, 64 Hz sampling)

SAMPLING MODES :

Fully simultaneous for 4 channels

FFT RESOLUTION : 

Min. 100 lines
Max. 3 276 800 lines

UNIT MODES:

Analyzer – analytical measurements
Data collector – route measurements
Balancer – 1 and 2 plane on site balancing
Run up – run up and coast down measurements
Recorder – raw signal recording for later post analysis
Stethoscope – listening of the bearing/machine noise
FASIT – expert system for automatic fault detection
MCSA
Octave analyzer – hearable sound measurements
Bump test – measurement of natural frequencies
ADS – Animated Deflection Shapes (Operating deflection shapes)
Ultrasound – measurement of ultrasound in 30 – 50 kHz range
Camera
IR Camera
Gallery

DISPLAY :

1125 x 800 pixels

BUILT IN CAMERA : 

5 MPx, autofocus

THERMAL IMAGING CAMERA (OPTIONAL):

384 x 288 pixels
-10°C ~ 150°C (or up to 250°C) temp. range
50 mK NETD sensitivity

PROCESSOR :

Intel Atom 1.9 GHz

MEMORY / ROUTE : 

64 GB, max. 16 GB for one route, number of routes is limited by free memory only

DATA PROCESSING :

Real time FFT
DEMOD – ENVELOPE analysis
ACMT – low speed bearing analysis
Order analysis
User band pass analysis
RPM measurement
DC measurement
Orbit measurement

RAW SIGNAL RECORDER :

64 kHz sampling frequency
4 Ch memory consumption 3 GB/hour
4 Ch total recording – 20 hours

TRIGGER : 

Manual, External, Signal level, Time
Speed change, Time interval

INTERFACE :

USB 3.0, 2.0 compatible

OPERATING TEMPERATURE RANGE :

-10˚C to +50˚C

POWER : 

Battery 8 hours of operation

CASE :

Aluminium heavy duty

SIZE AND WEIGHT :

29,5 x 23 x 4,9 cm, 2 Kg

LANGUAGES : 

English, Spanish, German, French, Portuguese, Russian, Czech, Hungarian, Polish, Romanian, Thai

VIDEO